Welcome, Guest.
Please login or register.
battery cable
Forum Login
Login Name: Create a new account
Password:     Forgot password

BAC Forum    General Boards    Technical Support  ›  battery cable Moderators: Gerald Farris

battery cable  This thread currently has 286 views. Print
1 Pages 1 Recommend Thread
Mel Griffin
February 23, 2010, 5:37pm Report to Moderator
BAC Member
Posts Per Day: 0.01
Upon reconnecting my battery cables to the coach batteries, I find a BLACK cable with this number 2504934 on it, according to my drawing I made when I took the cables off this BLACK cable goes to a RED post.  Can this be true?  Is there a place I can find this cable number to see if it really goes on a RED terminal?

Thanks for your help.
Mel


Miami Mel
2000 Patroit -40'
330 HP Cat
Logged Offline
Private Message
Richard And Babs Ames
February 23, 2010, 6:18pm Report to Moderator
Moderator
Posts Per Day: 0.07
If each coach battery has 6 cells (2 volts per cell) they are 12 volt and should be hooked up positive to positive (red to red) and negative to negative (black to black) to as your chassis is a 12 volt system like the house.

If you wire positive to negative you will be putting 24 into a 12 volt system.


1997 Beaver Patriot
3126B  CAT  
South Central FL
Logged Offline
Private Message Reply: 1 - 6
cnlshirk
February 23, 2010, 7:03pm Report to Moderator
Cream/Lt Blue 2001 Marquis Jasper/CAT C-12
Moderator
Posts Per Day: 0.03
Location: On the Road Again
Mel,
The two Negative posts should be connected together with a black cable and then another black cable is tied to a ground bolt on the chassis.
The two positive terminals should be connected together with a red cable and then another red cable is tied to the coach power.
Just be sure the positive cables are not connected to the ground bolt on the chassis. Where the cables go is more important than the color.  If you see a large spark, you did it wrong.
Larry
Logged Offline
Private Message Reply: 2 - 6
Gerald Farris
February 23, 2010, 8:55pm Report to Moderator

Board Moderator
Posts Per Day: 0.06
Location: FULLTIMER
Mel,
You did not say if the cable was going from battery to battery, or if it was going from the battery to the coach. If it is battery to battery, I can give you a very simple diagram to connect them up. If it is battery to coach, it takes a little more work to be certain you wire it correctly.

Gerald


2000 Marquis, C12
Logged Offline
Site Private Message Reply: 3 - 6
Joel Ashley
February 24, 2010, 6:56am Report to Moderator

Go OSU Beavers Class of '73 RVing 25 years
BAC Member
Posts Per Day: 0.06
Location: Clackamas, Oregon
Mel-

You said you were reconnecting your "coach" batteries, and if you mean the four 6-volt batteries (aka "house" batteries), then they are wired as 2 pairs, each pair hooked together in series, and the 2 pair wire to each other parallel;  your two 12-volt chassis batteries on the other hand are just hooked together in parallel.  A pair of 6v batteries wired in series provides 12 volts together.  A pair (or any number) of 12v batteries wired in parallel provides 12 volts together.  That can be confusing, so you should avail yourself of Gerald's diagram offer to make sure things are put back together right.

One thing I did on our old 1984 gas coach when replacing batteries, to identify multiple black cables that ran from up front up to 20 feet back to the converter and generator, was to make several wraps of red electrical tape around the insulation at the ends of the positive ones, and the same with green tape (or leave tapeless if you like) around the ground cables.  An ultra-fine point Sharpie permanent marker served to write on each tape which battery it went to - just ID each battery with a number, perhaps use a white marker to write a number on each battery (white nail polish works and lasts a long time).  A simple "2 +" on the taped end of a cable would tell you that end went on the positive post of battery #2.  A "3 - " would be the cable end that went to the negative post of battery 3.  The "permanent" marker fades after a few years, so be sure to refresh the markings occasionally.

Our Beaver coach is configured such that I haven't found it necessary to ID the cables yet, but if I ever do I might try foregoing the tape altogether and just mark the bats and black cables with white nail polish.  You just have to make sure the surface you want to mark is clean.


Joel and Lee Ashley
36 ft 2006 Monterey
C9 Cat
Beaver Believers
Logged Online
Private Message Reply: 4 - 6
Mel Griffin
February 24, 2010, 5:50pm Report to Moderator
BAC Member
Posts Per Day: 0.01
On 2-24-10 I was told by the Beaver people that cable # 2504934 was negative ground fo the inverter.  I lightly touched the black cable to negative post and got a big spark, then I touched the black cable to a positive post and no spark.  Upon finding info on Freedom Inverter at Coach Assist-Beaver Service Info by Steve Rankin, info says some inverters were shipped with both cables black, my red shrink wrap was missing.  Any way my original drawing showing black to positive post was right.  
See attached by Steve Rankin.

Mel



Attachment: document_7656.bmp
Size: 559.26 KB



Miami Mel
2000 Patroit -40'
330 HP Cat
Logged Offline
Private Message Reply: 5 - 6
Administrator
February 26, 2010, 7:30pm Report to Moderator
Administrator Group
Posts Per Day: 0.11
For those of you posting images, remember the file size equals image size.  Keep you file size under 100 KB and you images will fit on the page.  You can reduce the size of an image in any photo editing program.  You can use the email setting, that works well, or choose the smallest size available.  Image types that will post are BMP, GIF JPG


Tim Bentley
BAC Webmaster & Forum Administrator
webmaster.bac@gmail.com
Logged Offline
Site Private Message Reply: 6 - 6
1 Pages 1 Recommend Thread
Print

BAC Forum    General Boards    Technical Support  ›  battery cable

Thread Rating
There is currently no rating for this thread